09.29 / 2026

Mulch Film · End-of-Season Guide Mulch Film Removal and Recycling: What Buyers Need to Plan For Most buyers plan the laying of mulch film down to the day — and plan the end of it not at all. Yet the season’s last act decides two things: how much of the film’s recycling value survives, and how much plastic stays in your soil. This guide covers when to lift the film, why whole rolls earn more than shredded flakes, how to handle biodegradable film, and how to schedule next season’s order backwards from removal. ⏰ Removal timing ♻️ Rolls vs flakes 🌱 Biodegradable boundary 📅 Next-season planning At a glance Lift the film while it is still intact — after harvest, before UV embrittlement turns it into field litter. Work in half-dry weather: too wet and the film carries tons of soil; too cold and it snaps. Whole clean rolls earn far more than shredded flakes — contamination is the discount. PE and biodegradable film never mix in one disposal stream. Plan next season backwards from removal day — including the 30+ day lead time on the new order. Why the End of the Season Deserves a Plan Mulch film is...

View More

09.26 / 2026

Mulch Film · Technical Guide Mulch Film Lifespan: One Season, and How to Get Full Value From It Mulch film is designed to last one season — not because the quality is low, but because that is what the product is for. What “one season” actually means, the four things that shorten it, how black, clear, silver-black and biodegradable films differ, and how to get full value before the film comes off the bed. 📆 One growing season ⚫ Black · ⚪ Clear · 🌗 Silver-black ♻️ Biodegradable ≤ 30 mic 🛠️ Four lifespan factors At a glance A “season” is a crop cycle, not calendar months — from laying to removal, matched to your planting schedule. Four things shorten mulch film life: UV load, soil heat at the film edge, mechanical damage, and over-tension at laying. Black and silver-black PE mulch film hold one full season reliably when laid correctly. Clear film warms soil fastest but degrades quickest under UV — it is a soil-solarization tool first. Biodegradable film is capped at 30 mic and tills in at season end — it is not exempt from good laying practice. What “One Season” Really Means Mulch film is engineered against...

View More

09.25 / 2026

Greenhouse Film · Buying Guide Greenhouse Film Cost per Square Metre (and per Season): How to Compare Quotes the Right Way The cheapest roll on the quotation sheet is rarely the cheapest covering. Two quotes for “the same” film can differ by 30% in real cost once thickness, width, tolerance and service life enter the math. This guide shows how to convert any quote into cost per square metre — and then into cost per season, which is the number that actually decides. 💰 Cost per m² 📆 Cost per season 📏 Tolerance matters 📋 6-item quote checklist At a glance Price per kilo misleads: film is bought by area, so convert every quote to cost per square metre before comparing. Three numbers hide in every quote: nominal thickness, actual tolerance, and rated service life. Cost per season = (film + installation labor) ÷ seasons of production. A longer-lived film at a higher unit price usually wins this division. Wrong width is a hidden cost: non-custom widths mean offcut waste and extra seaming labor. A quote without tolerance in writing is an invitation to receive thinner film than you ordered. The Three Numbers a Quote Tries Not to Mention Every...

View More

09.23 / 2026

Greenhouse Film · Sizing Guide Greenhouse Film Width, Length and Seaming: How to Specify the Right Size A film ordered half a meter too short cannot be stretched to fit — and a whole roll can be written off in one morning of installation. This guide walks through how to measure width and length, what allowance to add for the channel and tensioning, when seaming is the right call, and the six things to send a factory before ordering a custom size. 📐 Width & length ➕ Allowance rules 🧵 When to seam 🌬️ Windward reinforcement 12 mMax single-piece width 100–200Mic range 6Details to send us 30+Days lead time Sizing at a glance Measure the arch, not the floor: film covers the curved surface, so width follows the arc length over the bow plus both anchoring ends. Add allowance for the channel — film must push into the locking profile on both sides, typically 20–30 cm per side. Add tension allowance: film stretches when tensioned; better 20 cm too long at the anchor than 5 cm short. Seam only when necessary: above roughly 16 m of total developed width, plan a factory seam — and position it away from the...

View More

09.16 / 2026

Technical Guide · Greenhouse Film Greenhouse Film Installation & Maintenance Guide: Fit It Right, Make It Last The same roll of film can give two very different results. Fitted correctly, a UV-stabilised greenhouse film reaches its full service life; fitted badly, it tears at the channel in the first winter or drips on the crop from day one. This guide covers what our export team walks buyers through before every container ships. 100–200 mic90% Light TransmissionPO 3–5 YearsUp to 16 m Width 100–200Thickness (mic) 90%Light Transmission 3–5 yrsPO Service Life 16 mMax Film Width At a Glance — Five Steps That Decide the Life of the Film Check the frame first — burrs, sharp edges and rust points puncture film from the inside, usually weeks after installation. Which side faces in matters — anti-drip layer inside, UV-stabilised layer outside. Reversed film means condensation drips on the crop and a shorter service life. Tension in stages — drum-tight, not stretched thin. Loose film flaps and wears; over-tensioned film thins at the channel. Fix perimeter and windward side first — most failures start at the edge, not the middle of the span. Maintain by season — dust, snow load, loose locking channel...

View More

09.09 / 2026

Buying Guide · Film Comparison PO Film vs PE Film: Which Greenhouse Film Should You Choose? PE and PO greenhouse films look almost identical on a roll — but they behave very differently over three seasons. This comparison walks through light transmission, lifespan, heat retention, anti-drip performance and the real cost per season, so you can decide with numbers instead of price tags. ⚖️ Head-to-head 💰 Cost per season ☀️ UV lifespan 💧 Anti-drip 30+Years making film 55,000 tAnnual film capacity 100+Countries supplied 5-layerCo-extrusion line PO vs PE — At a Glance PE film is the budget workhorse: cheap, light, easy to install — but single-layer PE typically lasts 1–2 years under real UV load. PO film (polyolefin) is co-extruded in 3 or 5 layers with a UV stabilizer package: up to 90% light transmission and a 3–5 year lifespan. The deciding number is cost per season, not price per square meter — a film that lasts 4 seasons at a higher unit price usually wins. PE still makes sense for short-cycle crops, seasonal tunnels and tight first-year budgets. PO wins for multi-season vegetables, high-value crops, strong-UV regions and anywhere replacement labor is expensive. What PE and PO Films Actually...

View More